GLOW blend Dosage Calculator
A popular cosmetic recovery blend of GHK-Cu, BPC-157, and TB-500 sold in one vial.
Total amount printed on the vial label.
Changes concentration only — your dose stays the same.
2000 mcg = 2 mg
1 mL barrels are sold marked two ways: 0–100 insulin units (U-100) or 0–1 mL (tuberculin / luer). Same volume — 100 units = 1 mL — so the result below gives you both readings.
1.0 mL (100-unit) · top row = insulin units, bottom row = mL · smallest mark = 2 units · check yours, gradations vary by brand
Show the math — every step, with your numbers
- Concentration: 70 mg ÷ 5 mL = 14.00 mg/mL (14000 mcg/mL)
- Dose volume: 2000 mcg ÷ 14000 mcg/mL = 0.143 mL
- Syringe units: 0.143 mL × 100 = 14.3 units
How much water should I add?
The same 2000 mcg dose from your 70 mg vial, at each water volume. More water spreads the dose over more units, which is easier to read accurately. Tap a row to use it.
Calculated on a U-100 insulin syringe (100 units = 1 mL). This is reconstitution arithmetic for GLOW blend, not a dosing recommendation. Verify against your product label and a qualified professional.
GLOW blend reconstitution chart
Concentration for each vial size when reconstituted with 5 mL of bacteriostatic water. Change the water amount in the calculator to see other concentrations, or open the full reconstitution chart to compare every dose and water volume at once.
| Vial size | Bac. water | Concentration | Per unit (0.01 mL) |
|---|---|---|---|
| 70 mg | 5 mL | 14.00 mg/mL | 140.0 mcg |
| 80 mg | 5 mL | 16.00 mg/mL | 160.0 mcg |
About GLOW blend dosing
GLOW blend (GLOW (GHK-Cu + BPC-157 + TB-500)) is a popular cosmetic recovery blend of GHK-Cu, BPC-157, and TB-500 sold in one vial. It is commonly sold in 70 mg, 80 mg vials. Commonly-cited community and research protocols reference a range of 1,000–3,000 mcg, daily in cited protocols. The vial mass is the combined total of all three peptides; check the label ratio for per-peptide amounts.
Remember that the number of syringe units for any dose depends entirely on how much bacteriostatic water you add. The calculator above is pre-filled with a common setup for GLOW blend; adjust the inputs to match your own vial and the units update instantly.
Check GLOW blend for yourself
The figures on this page are commonly-cited references for the arithmetic, not prescriptions. These are primary, non-commercial sources where you can verify them independently.
- GLOW blend studies on ClinicalTrials.gov ↗
Registered human studies, their doses and protocols. If a compound has few or no registered trials, that is worth knowing before relying on any figure.
- GLOW blend on PubChem ↗
Chemical identity and molecular weight from the NIH.
GLOW blend calculator — FAQ
How do I reconstitute GLOW blend?+
The vial mass is the combined total of all three peptides; check the label ratio for per-peptide amounts. Add your chosen amount of bacteriostatic water to the vial, swirl gently (never shake), and use the calculator above to convert your target dose into insulin-syringe units.
What is a common GLOW blend dose?+
Commonly-cited protocols reference 1,000–3,000 mcg, daily in cited protocols. These are references for the arithmetic, not a prescription — confirm with your product label and a qualified professional.
How many units of GLOW blend should I draw?+
That depends on your vial size and how much bacteriostatic water you added. Enter both into the calculator above along with your dose and it shows the exact units on a U-100 insulin syringe.